SureStrip
Fast Acting Sealer Stripper

  • Powerful Stripping Technology: Strips Away a Variety of Sealers & Coatings
  • Fast Acting: Works in Minutes
  • Safe For Most Surfaces: Does Not Damage or Etch Surfaces
  • Ready to Use Formula: No Dilution Necessary
  • Clean Rinse Technology: Sealer & Stripper Residue Rinses Away Easily

SureStrip is a technologically advanced stripper designed for removal of acrylics, acrylic latex, polyurethane and other resin coatings and sealers. It can also be used as a spot cleaner to remover paint spots. SureStrip is recommended for outdoor use only and works best on horizontal surfaces. SureStrip’s Clean Rinse Technology allows old sealer and stripper residue to be quickly and easily rinsed away with a low or high pressure washer.  SureStrip is ready-to-use and should not be diluted. SureStrip will remove most Surebond film forming sealers.  Not appropriate for use with SB-4000, SB-4400, SB-5000, SB-6400, SB-6700 and SB-6750.

Suitable Surfaces

Suitable for concrete and clay pavers, flat and stamped concrete, masonry, natural and manufactured stone, segmental retaining wall blocks, concrete walls and exposed aggregate. Can also be used on tile, terrazzo and stucco.  Safe to use on surfaces in outside environments. Use caution on sensitive surfaces such as wet cast pavers and stamped concrete as it may cause damage to color of the surface. Not for use on asphalt. Test first to verify suitability and dwell time before stripping the entire surface.

SureStrip is compatible with all Surebond Sealers. A test area is always recommended to determine product suitability and compatibility with your specific surface before use and also if desired results are achievable.

Coverage Per Gallon

Application Sq.Feet Sq.Meters
All Surfaces 125 – 250 11.6 – 23.2

 

Coverage based on single treatment. Some applications may require additional treatments. Coverage rate may vary depending on the surface porosity, texture, severity of staining, application method and local conditions.

Click below to open up the tab to reveal more information.

SureStrip Helpful Information

Preparation/Pre-Testing

Remove all loose soil and debris from the surface. Cover and protect adjacent and surrounding surfaces not intended to be stripped from old sealer, stripper and rinse water. Caution: SureStrip will remove paint from painted surfaces. Spray water on adjacent plants and grass to limit potential absorption of stripper. Cover foliage with plastic sheeting or other proven protective material. It may be necessary to manage rinse water containing old sealer and stripper by reclamation to prevent run-off into storm sewer. Small scale projects can be dammed and residue removed with a shop vac. Large projects or volume of residue can be removed with a reclamation unit. TEST FIRST:  Before using SureStrip, test on a small inconspicuous area following the application instructions to determine the suitability for removing the desired sealer from the surface. Allow test area to dry thoroughly before evaluating final appearance and results. Testing should confirm effectiveness of stripper and necessary dwell time.

Application Information

Use SureStrip when air and surface temperatures are 40° F or above. If freezing conditions exist, allow time for the surface to thaw. If air temperatures exceed 90° F, flash cool the surface with water before applying product. Do not allow product to dry on a hot surface. Rinse thoroughly while stripper is still wet on the surface. Always perform a pre-test (refer to Pre-Test Instructions). On large projects, it may be necessary to work in smaller more manageable sections.

Application Tools:  low-pressure high-volume sprayer, clean stiff bristle brush or broom, flat surface cleaner attachment (optional), cold pressure washer with 25° to 40° tip

Application Instructions:  SureStrip is designed for one application stripping. Additional applications may be needed to remove some sealers. Do not dilute. Apply SureStrip using a low-pressure sprayer. If surface is sloped, apply SureStrip from bottom of slope working upwards using a side-to-side motion. Allow SureStrip to dwell for 10 – 15 minutes. Do not allow SureStrip to dry on the surface during dwell time. Re-apply SureStrip if necessary to keep the surface wet with product. Perform a test by scratching the sealer with a sharp object to see if the sealer lifts from the surface. If sealer is gummy but not released, allow to dwell for an additional 10 minutes before re-testing. Re-apply SureStrip if starting to dry. Improve results by scrubbing surface with a brush, broom or flat surface cleaner to agitate and remove sealer. Rinse surface thoroughly with a cold water pressure washer or garden hose with nozzle. Only use as much pressure needed to thoroughly clean surface. Excessive high pressures can damage substrate. Before installing joint sand or sealing, allow surface to dry completely.

Clean Up

Rinse all tools and overspray thoroughly with water before product dries.

SureStrip Demonstration

Five Steps to Hardscape Restoration

SureStrip Install

Coming Soon..